Netgear AX1800 | EAX20 installation guide

The Netgear AX1800 mesh repeater is based on the new generation WiFi 6 technology and is meant to give incredible WiFi intensity, high speed, and improved coverage using the fresh era WiFi 6 standard. All that’s remaining to do now is complete the Netgear EAX20 Setup and find delight in a better-connected home. WiFi rates of up to 1.8 Gbps can be achieved with the AX1800 EAX20 WiFi booster, which can be used even in the most remote parts of your house.

Two wired devices will benefit from the mesh extender’s four-stream WiFi and additional spatial channels, which provide more usable bandwidth and less latency than a single stream WiFi connection. The EAX20 Extender is an excellent choice for medium-sized families.

You can find widespread instructions for configuring the Netgear EAX20 AX1800 WiFi range repeater on this page as well. Let’s get the festivities underway.

AX1800 WiFi extender Netgear EAX20 deployed in minutes and with no effort. They’ll help you through each procedure to create that your extender is set up correctly the first time.

WPS Method | Netgear AX1800 extender:

In order to configure the Netgear EAX20 AX1800 to use the WPS push button, please follow the steps below:

  • consider Turning on the dual-band WiFi mesh repeater EAX20 AX1800 by pressing the power button.
  • The WiFi extender and router should be kept in the same area.
  • Make sure your extended cord is plugged into an electrical outlet until it is finished.
  • Wait for the EAX20’s Power LED to turn orange before proceeding.
  • On the extender, push the WPS button once.
  • If the Netgear EAX20 Setup Leds is lit up white, this indicates that the connection between your network and booster is working properly.
  • Make the necessary adjustments to the position of your extension.
  • Take your WiFi-enabled computer or mobile device to a location where the WiFi router coverage is poor or non-existent.
  • The Extender network can be joined using a computer or mobile device that is WiFi-enabled.

That’s how you finish up your Netgear EAX20 configuration by pressing the WPS button. If you encounter any technical glitches throughout the configuration process, please contact our technical support team for assistance.

Netgear EAX20: Manual method

Manually installing the AX1800 4-stream WiFi booster is simple if you follow the directions below:

  • Connect the Netgear AX1800 WiFi mesh extender model EAX20 to the internet via a wired or wireless connection.
  • Use an immediate vicinity to your router while placing the WiFi extender.
  • Last but not least, connect the extender to a power supply.
  • Continue to hold your breath until the Power Light flashes green on the monitor.
  • If the Power LED does not illuminate, press the Power button to turn on the computer.
  • Wi-Fi or Ethernet are the best methods of connecting your Netgear EAX20 WiFi range booster.
  • On a computer or mobile device, open a web browser and type mywifiext.net into the address bar.
  • The Netgear AX1800’s login screen will show on the screen.
  • The on-screen instructions will guide you through the process of connecting your extender to an established WiFi network.
  • Make the necessary adjustments to the position of your extension.
  • The extender may not connect unless it is moved closer to the router. If this is the case, try again before the Connection Success LED goes white.
  • Link your user PCs to the extender’s WiFi network after you’ve determined the best position for your extender.

If you’re still experiencing trouble configuring your Netgear EAX20 AX1800 Extender, please feel free to contact with one of our highly skilled technicians.

Firmware Update:

  • Make sure that your Netgear AX1800 WiFi extender is turned on first before proceeding.
  • Connect your router to the extension using an Ethernet cable.
  • After that, open your preferred web browser of choice.
  • In the address bar, type mywifiext.net and press the return key.
  • Log in to your extender using your login and password to complete the process.
  • To upgrade the firmware, go to the setup menu and select Firmware Upgrade from there.
  • To complete the process, click on the Check button once again.
  • If a new version of the Netgear EAX20 AX1800 firmware is available, select Yes to upgrade the firmware.
  • Allow enough time for the Netgear extender AX1800 to complete the necessary firmware upgrades.

Our conversation has come to an end. Attempts have been made to modify the firmware of your extender. If you have any questions or concerns, please do not hesitate to contact our staff.

Leave a Reply

Your email address will not be published. Required fields are marked *