Are you new to AutoCAD? Are you trying to figure out how AutoCAD works? If yes, we are assuming that you are stuck somewhere and that is why you are here looking out for help. If not, then you must be a newbie to the world of AutoCAD. For either of the two reasons you are here for, we are here for only one reason. And that is to help you learn autocad assignment help. To ease the process, we have explained the steps to how to use AutoCAD. 

If you want to learn to run, you first need to learn to walk. Similarly, to learn AutoCAD, you need to learn it step-by-step. 

But before we start out with the steps. Below are some tips that you should consider before learning AutoCAD.



  • The first step is so obvious. And you are even doing it right now. That is to look out for help online. Go through various websites and videos which are specifically providing information about AutoCAD.
  • Regularly search for new and different exercises. This will help you memorize various lessons. 
  • Start off with learning 2-dimensional drawing tools and apply them to make 2-dimensional drawings. You can also search online for 2-dimensional drawings, you will get plenty of them. Once you get a grip on creating 2-dimensional drawings, then slowly shift to 3-dimensional drawing. Because they are similar to that of 2-dimensional drawings with some specialized tools.

Practice, practice, and practice. “Practice makes the man perfect” applies to everything. AutoCAD is no exception. Practice AutoCAD as much as I can. 

Now you can follow the below steps to learn how to use AutoCAD.





Draw a 625-foot-radius circle.


Step 2: Make a new circle.

Draw a circle with a radius of 312.5 inside the circle from step 1.


Step 3: Adding Lines. 

Draw a line with a length of 2312 from the center of the circles to the right.


Step 4: Connect the Circles to the Lines.

Draw a circle with a radius of 876 at the end of this new line.


Step 5: Choosing an Angle

Draw a new line from the center of the circle formed in “step 1” for a length of 2312 with a 40-degree angle between this line and the one created in “step 3.”


Step 6: Create a new circle.

Create a new circle with a radius of 876 at the end of the newly inserted line.


Step 7: With a radius of 2312, draw a circle with the same center point as the circle from step 1.


Step 8: With a radius of 437, draw two circles, one with a center precisely on the center points of the circles generated in stages 4 and 6, and the other with a center exactly on the center points of the circles created in steps 4 and 6.


Step 9: Trimming.

You’ll get the following image if you trim circles.


Step 10: Trimming.

Trim the circle with a radius of 2312 with the two lines with a 40-degree angle between them till you obtain the image below.


Step 11: With a value of 876, create an offset to the left and right of the previously created arc.


Step 12: Draw a line with a length of 3492 and an angle of 180 degrees from the center of the circle in step 1 to the left.


Step 13: Draw a 626-radius circle on the terminal point of this new line.


Step 15: Draw a vertical line that divides the two circles in half and trims the right arcs to get the form below.


Step 16: We now have two arcs. Add a horizontal line with a length of 1000 at each of their ends.


Step 17: Using the mirror tool, duplicate those arcs until you achieve the shape shown below.


Step 18: Add dimensions, based on the original image on the first page of this file, and include the 1875 and 750 dimensions lines.


Step 19:

Add a line at the junction of those measurements, then a circle with a radius of 437.5 and a center point as the center of this line.


Step 20. Draw a circle with an 875-radius from the same center point.


Step 21. Draw a circle with a radius of 1375 and a center point that is the same as the original circle from step 1.


Step 22. Draw a vertical line through the center of this circle and trim it to the original shape until you get the following item.


Step 23. Draw a line from the new arc’s endpoint to the arc’s point on the left side of the screen until you get something like this.


Step 24: Using the fillet tool, link the arc formed in step 11 with the arc created in steps 21-22, but use a radius of 625 for the fillet radius.


Step 25. Repeat steps 11–25 with a radius of 625 for the top of the arc generated in step 11.


Step 26.

The final step is to use the fillet command to build an arc between the circle generated in step 20 and the outer arc created in step 17 with a radius of 1750 fillet radius.


Step 27: Join the unconnected lines of the arcs you made in step 17 together.


28th step.

Remove the additional lines that were created for the measurements alone, and you’ll get the final shape.



These were the steps to how to use AutoCAD. We hope it was easy and clear for you to understand and catch.

To read about these steps in details check out




  1. What is AutoCAD?

Ans. AutoCAD is a drafting software application that allows users to produce exact 2- and 3-dimensional drawings for use in building and manufacturing.


  1. Is it possible to design a geothermal power plant floor plan using AutoCAD?

Ans. Yes, you can, and you should do so in 2d. Begin with constructing the perimeter, then the inner walls, and last the machines and furniture.


  1. On a current drawing, how do you alter the size?

Ans. If you’re using AutoCAD, you may set size limitations in millimeters or inches.

Leave a Reply

Your email address will not be published. Required fields are marked *